这几天一直在测试PWM，CCR4的中断，ADC1的采样触发+DMA等功能，现在也了解的差不多了，先记录下来，先看下我的一些设置，TIM1设置：
1 /* Time Base configuration ,init time1 freq*/ 2 TIM_TimeBaseStructure.TIM_Period = Period; 3 TIM_TimeBaseStructure.TIM_Prescaler = 0; 4 TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; 5 TIM_TimeBaseStructure.TIM_ClockDivision = 0; 6 TIM_TimeBaseStructure.TIM_RepetitionCounter = 0; 7 TIM_TimeBaseInit(TIM1, &TIM_TimeBaseStructure); 8 9 /* Automatic Output enable, Break, dead time and lock configuration*/10 TIM_BDTRInitStructure.TIM_OSSRState = TIM_OSSRState_Enable;11 TIM_BDTRInitStructure.TIM_OSSIState = TIM_OSSIState_Enable;12 TIM_BDTRInitStructure.TIM_LOCKLevel = TIM_LOCKLevel_OFF;13 TIM_BDTRInitStructure.TIM_DeadTime = 0;14 TIM_BDTRInitStructure.TIM_Break = TIM_Break_Disable;15 TIM_BDTRInitStructure.TIM_BreakPolarity = TIM_BreakPolarity_High;16 TIM_BDTRInitStructure.TIM_AutomaticOutput = TIM_AutomaticOutput_Enable;17 TIM_BDTRConfig(TIM1, &TIM_BDTRInitStructure);18 19 /*pwm driver set ，channel 1,2,3,4set pwm mode*/20 TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;21 TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Disable;22 TIM_OCInitStructure.TIM_OutputNState = TIM_OutputNState_Disable;23 TIM_OCInitStructure.TIM_Pulse = 5;24 TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;25 TIM_OCInitStructure.TIM_OCNPolarity = TIM_OCNPolarity_High;26 TIM_OCInitStructure.TIM_OCIdleState = TIM_OCIdleState_Set;27 TIM_OCInitStructure.TIM_OCNIdleState = TIM_OCNIdleState_Set;28 //set OC1/OC1N29 TIM_OC1Init(TIM1, &TIM_OCInitStructure);30 //set oc2/oc2n31 TIM_OCInitStructure.TIM_Pulse = 0;32 TIM_OC2Init(TIM1, &TIM_OCInitStructure);33 //set OC3/OC3N34 TIM_OCInitStructure.TIM_Pulse = 0;35 TIM_OC3Init(TIM1, &TIM_OCInitStructure);36 //set adc sample time37 TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;//CCR4这个输出使能后才能用来触发ADC1的注入通道采样38 TIM_OCInitStructure.TIM_Pulse = 0; 39 TIM_OCInitStructure.TIM_OCIdleState = TIM_OCIdleState_Set;40 TIM_OC4Init(TIM1, &TIM_OCInitStructure);41 42 //enable interrupt43 TIM_ITConfig(TIM1, TIM_IT_CC4, ENABLE);//CCR4的中断，这个通过设置CCR4的pulse来控制产生中断相当于PWM-ON的位置44 TIM_ITConfig(TIM1, TIM_IT_Update, ENABLE);45 TIM_ITConfig(TIM1, TIM_IT_COM,ENABLE);46 47 /* BLDC_TIMER_NUM counter enable */48 TIM_Cmd(TIM1, ENABLE);49 50 /* Main Output Enable */51 TIM_CtrlPWMOutputs(TIM1, ENABLE);
ADC1设置，这里采用规则通道+DMA+软件触发，注入通道+CCR4事件触发：
1 ADC_InitStructure.ADC_Mode = ADC_Mode_Independent; 2 ADC_InitStructure.ADC_ScanConvMode = ENABLE; 3 ADC_InitStructure.ADC_ContinuousConvMode = DISABLE; 4 ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None; 5 ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right; 6 ADC_InitStructure.ADC_NbrOfChannel = 5; 7 ADC_Init(ADC1, &ADC_InitStructure); 8 9 ADC_TempSensorVrefintCmd(ENABLE);10 ADC_RegularChannelConfig(ADC1,ADC_Channel_0,1,ADC_SampleTime_239Cycles5);//hand11 ADC_RegularChannelConfig(ADC1,ADC_Channel_1,2,ADC_SampleTime_239Cycles5);//external temperature12 ADC_RegularChannelConfig(ADC1,ADC_Channel_2,3,ADC_SampleTime_239Cycles5);//vol13 ADC_RegularChannelConfig(ADC1,ADC_Channel_10 ,4,ADC_SampleTime_239Cycles5);14 ADC_RegularChannelConfig(ADC1,ADC_Channel_Vrefint,5,ADC_SampleTime_239Cycles5);15 //上面规则通道的设置，注意采样时间，我发现如果时间设置过的可能数据会互相干扰16 //下面是注入通道，这里注入通道设置成TIM1的CCR4事件触发17 ADC_InjectedSequencerLengthConfig(ADC1, 1);18 ADC_InjectedChannelConfig(ADC1,ADC_Channel_TempSensor,1,ADC_SampleTime_7Cycles5);//CURRENT 19 ADC_ExternalTrigInjectedConvConfig(ADC1, ADC_ExternalTrigInjecConv_T1_CC4);//这个可以使用time1的CCR4事件来触发采样20 ADC_ExternalTrigInjectedConvCmd(ADC1,ENABLE);21 22 ADC_ITConfig(ADC1,ADC_IT_JEOC,ENABLE);//ENABLE INJECTED INTERRUPT23 /* Enable automatic injected conversion start after regular one */24 // ADC_AutoInjectedConvCmd(ADC1, ENABLE);//是否在规则通道结束之后自动开始注入通道采样25 26 27 ADC_DMACmd(ADC1, ENABLE);28 29 ADC_Cmd(ADC1, ENABLE);
另外我还加了一个注入通道采样结束的中断，用来快速处理相电流的一些问题，比如限流、过流的处理。
测试从发现如果把CCR4的pulse设为0，那么就不会触发ADC1的注入采样，也就不会产生ADC的中断，只有pluse设置为一定的有效数值，那么adc注入通道的采样才会被触发。